Clear Sunglasses Case

I initially made this because I wanted to play around with the PVC I bought but it turned out pretty well so I decided to post it. Hence why I didn't document the earlier stages of the DIY. (:

 You will need:

Transparent PVC, I got a 0.5mm table top protector 

Seam pickers

Studs with screws

Scissors

Paper

Tape

On paper draw a rough trapezium around the glasses and mirror the shape for the closing flap.

Add the side flaps by drawing two more trapeziums, both with a downward slope.

Finally draw the bottom flap which should be about half the height of the main panel. 

Cut out the template and make a mock case by folding the edges. Then trim any excess off if necessary. Tape the final template onto the PVC and then cut out.

Use the seam pickers or any thick needle and make a small hole where the black circles are.

 Fold over the side flaps and screw the stud bases through the holes as pictured.

 Screw the top studs onto the base.

Then fold the top flap over and use a hole punch to create a hole where the flap meets the stud.

A clear case for my clear sunnies!

'Button' Rings

 My laptop is still in a coma but I really wanted to get a post out before my uni week began again. I went to Lincraft on the weekend and spotted these interesting buttons so I made them into rings. 

 You will need:

Buttons; I found this cool crescent moon button and this silver stamp button which had this hieroglyphic kind of symbol

Ring bases; a gold and a silver to match the buttons

Superglue

Pliers

 Use the pliers to remove the button loops. If the loops don't come off clean, you may need to use a nail file or rough sandpaper to smooth it down.

 Simply superglue the ring bases onto the buttons and your rings are good to go!

DIY Whiteboard / To Do List

 So this whiteboard frame has actually been on my to-do list for a while now. I've been doing lots of home decor-ish DIYs and we've got another one!

 You will need:

Any old photo frame + the glass

Spray paint / paint 

Whiteboard Markers!! (which I forgot)

I chose black for the spray paint because I've noticed that my room has been getting a bit too white, too sterile for my liking.

I also tried to find a frame that has a bit of detail so it'll catch the light and not look too flat.

 Paint the frame with 1 or 2 even coats and let it dry.

 Then I whipped up my to-do list on word because I'm pathetic at photoshop.

Note the clock; how cute / tacky of me.

Print it out, cut to size, slide it into your frame and you've got yourself a snazzy to-do list that might actually encourage you to get things done!

I would write "buy markers" on my list... if I any to begin with.

I really need to get myself sorted.

Short Room Tour

There's a snippet of the finished aspects of my room!

 Left | Cut Lace Vanity Tray | Urban Outfitters

 Right | White Roses | DIY

2nd from Right | Spray-painted Mesh Pencil Tin | DIY

 Astrological Ring Stand | Urban Outfitters

Spinning Ribbon Earring Stand | Urban Outfitters

Necklace Holder | DIY

I just removed the tree bit of my old IKEA Statist jewelry stand and hooked it onto my wardrobe door! 

My column of sticker photos in my wardrobe :)

 The corner above my bedside table

Penguins & Magazines

 Ribba Frames in White | IKEA

 Images from RUSSH & Oyster magazines

Ombre Jewelry Display Stand

Borrowing the idea from Weddings and Cookies' Cookie Stand DIY, I made myself a white-to-clear ombre stand for all my bracelets and bangles. (Hopefully you can somewhat see the ombre effect in the mirror!)
 I don't mind the look of the stand being complete white but I think the glass of the candlestick makes it stand out and look a bit more expensive than it is.
You could do all sorts of shapes and sizes, mix and match to store all your rings, nail polishes, lipsticks etc!

 You will need:

Plate; ones with interesting detail turn out well

Candlestick; preferably one with a flat top so it'll be easier to glue

Newspaper

Glossy White Spray Paint

Superglue

 Apply superglue to the top of the candlestick

Wait until the superglue has turned tacky before turning over and gluing to the center of the plate.

 Start spray painting!

To create the ombre effect, just avoid aiming the spray paint directly at the candlestick and loose particles of paint will gather at the top of the candlestick anyway
After that's dried, turn it over and spray paint the the other side.

If you're worried about getting paint on the bottom, wrap it up in newspaper

And you should be left with this!

 

If you're going to use this as a cake stand, you'll want to seal the spray paint with some sort of sealant but if you're using it for non-food purposes, you're done!!

Ballet Pointe Flats

In addition to the Chloe & Monki shoes from my En Pointe post, I've seen more and more flats inspired by actual ballet pointe shoes like these from Urban Outfitters. So finally here's my DIY version!

You will need:

Ballet Flats - $20

Matching Thread

Needle

4 x 50cm Ribbon

Candle / Lighter; any sort of flame

I got my flats from Rubi Shoes which I recommend for this DIY because they have the loop at the heel & the elastic trim around the shoe which makes this DIY a lot easier. 

*The ribbon should be thin enough to fit through the loop and the thread should match the elastic trim.

Firstly, light a candle and slowly bring the each ribbon end close to the open flame. The edge will start to melt so you'll need to move the ribbon back and forth to seal it. Altogether you'll need to seal all 8 edges and make sure all the ends are cool and no longer tacky before you touch them.

Try on the flat and carefully pin the ribbon to where the top of the arch of your foot meets the shoe (or alternatively just pin the ribbon to the middle of the elastic trim).

Also you'll need to thread the needle.

 Leaving the pin in the ribbon, start sewing the ribbon onto the elastic trim from the inside, in a cross pattern. 

Once it's secure enough, slide the needle off and tie the loose ends of the thread.

By leaving the pin in, the stitches will be loose enough to allow the elastic to stretch when you wear it.

This is what it'll look like on the outside, the thread will be hardly noticeable from afar.

Repeat all the steps on the opposite side of the flats, making sure that they match. If you're in doubt of where to sew the ribbon, pin it and try it on first.

And repeat all the above steps with the other shoe!

Lastly, thread the ribbons through the loop, making sure that the ribbons go through without twisting.

 And there you have it!

Copper DIYs

 I drove (yesss) to Bunnings the other day and I found more wicked copper plumbing bits. The whole lot only cost me about $5 which amazing since they're so different to what's available at the usual craft stores and I have 3 DIYs using them.

 The compression olives (I'm guessing that's what they're called) were about $3 and it came in a pack of 10; 5 copper rings and 5 nylon rings.

 The 20mm pack is the perfect size for your fingers and since there are so many they're stackable!

 For the capillary elbow, I just chucked it on a black ribbon. I think it's the perfect piece on a plain white top or for layering with other necklaces.

 Since the capillary tee is such a unique piece, I thought that it would be a great foundation for a statement necklace. 

 I first slid the tee onto a gold chain and then pulled the chain through the bottom of the tee.

 I found the middle of the chain; very important otherwise your necklace will be lopsided! and then used a jump ring to loop a rose pink tassel onto the chain.

 The finished product of the tee necklace against my very dirty wall. 

Obviously you can use any coloured tassel but I think the pink and the copper go very well together. 

And there we have 3 DIYs for next to nothing!